Knowing Plumbing Basics is Essential When Installing a Bathtub
Knowing Plumbing Basics is Essential When Installing a Bathtub
Blog Article
The content listed below on the subject of Tools You Need to Install a New Bathtub is fairly engaging. Read it yourself and figure out what you think of it.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is also a moderately difficult job. If the old tub is conveniently available, the project can move rapidly; if you need to open up a wall surface to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will require an assistant to vacate the old tub and also embeded in the brand-new one. Make sure you have actually qualified on your own for the job and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is much better to think about using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This article will aid you mount a brand-new bath tub in your bathroom if you have already gotten a new tub and do not require to change the arrangement of your previous water pipelines.
Your tools as well as material list ought to consist of the following:
Preparing for the Installation
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the limited gain access to that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bath tub
Using both wood boards under its feet, put the tub in the needed placement. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile tap adapter to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Activate the supply of water and examine all joints and new pipework for leaks and also tighten them if necessary. Fill the bath tub as well as additionally check the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the bathtub should wait up until the tub has actually been made use of a minimum of when as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the tap as well as the sink. Secure the faucet in position with the manufacturer provided backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former type needs to be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can split fairly very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily available on the marketplace. It is advisable to fit the tiles using water-resistant or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog post on How to Install a Bathtub Yourself when doing a search on the internet. Enjoyed reading our piece of writing? Please share it. Help other people check it out. Thanks a bunch for your time. Visit again soon.
Leading plumbing expertise for emergencies. Report this page